Safety Record keeping

Safety record keeping is more than just the OSHA Log. Records of inspections, training, audits, corrections, and other safety activities can help you in the event of an OSHA inspection. Additionally, a good safety record-keeping system of using these safety forms will allow you to track changes and trends which is essential in reducing workplace accidents, injuries, and illnesses.

This article will outline the benefits of Recordkeeping and measuring the result of workplace safety performance

Evaluating Safety

Measuring the results of workplace safety and health changes benefits employers and employees because both gain confidence that the change results in a safer workplace. Since most changes occur by trial and error or in stages, information about the effectiveness of each stage is naturally helpful to the process. These changes often result in increased productivity and demonstrate that employee safety and health can be a good investment. Employees must be involved throughout the selection of safety changes and their measurements.

Step 1: Form a team

Evaluations are best done by a team. When forming a team, keep in mind that workers are often the best source of information about the workplace.
Wherever possible, the team should include people who are
• affected by the safety and health change,
• responsible for implementing and maintaining the change, and/or
• involved in future decisions about changes.
The team should start by defining the problem as clearly as possible. The more specifically that the problem is defined, the better that a solution can be designed to fit, and the easier it is to test the solution. Brainstorm a solution for the problem and one or two ways to measure the effectiveness of the change. Using more than one way to measure the change will increase your confidence in the results.

Step 2: Collect Relevant Data

Collect accurate data on workplace safety and health. Consider collecting three kinds of data: conditions before the change, information about how the change was put in place, and what happened after the change was made. Good records of how the change was made will help if you want to do it again because they tell you what happened. Data on the outcome will tell you whether to bother doing it again.

How, how often, and when should you collect data?

One way is to measure an outcome (like employee injuries) before and after the change. Typically, injuries are infrequent occurrences; therefore, you may need to collect data for quite a while before and afterward to make sure that any changes you detect are real. On the other hand, if you are measuring changes in employee knowledge and attitudes after a training session, you may not need to measure for as long a period of time. You may measure immediately before the training, right after the training, and then one or two more times 3 months to 1 year after the training.

Another model for gathering information is to arrange the change so that it does not affect everyone in the operation at one time. By introducing the change to several different groups over a period of several months or a year, you can get a better idea of effectiveness. Simply measure all the groups (those who receive the change immediately and those who receive it later) at regular intervals as you gradually introduce the change to the selected groups. This takes more effort, but it gives you added confidence that any detected effects are from the change and not some other event.

What to measure depends on the following:

• Expected outcomes – what will happen as a result of the safety and health change? Whatever you expect – reduced injuries or absenteeism increased productivity, — measure those things.
• Nature of the safety and health change – for example, if the change is plant exhaust ventilation, then you may want to measure air quality before and after. If the change is increased rest breaks for employees, then you may want to measure productivity. If the change is new training, then you may want to look for performance indicators or success/failure rates.
• Opportunity – think of measurements that are practical. Remember that someone or something has to collect and analyze the measurements you choose.

Here are some simple ways of collecting data. If you use more than one of these methods to measure each change, you will be more certain of the results.

Here are some simple ways of collecting data. If you use more than one of these methods to measure each change, you will be more certain of the results.
• Records
• Several types of records can provide data on the effectiveness of safety and health changes.

Useful data include the following:

•  Injury frequency and rates
• workers compensation costs
• Lost workdays and absenteeism due to work-related injuries
• Profit and loss
• Air sampling data, noise readings
• Production errors or waste
• Cost of respiratory equipment or ear protection
• Records should be checked for completeness and accuracy before they are used.

Surveys

Surveys are useful for determining workers’ perceptions both before and after a change:

Pre-change assessment

• What is working well?
• What is working poorly?
• Where in the work process are there delays in production?
• Where can quality be improved?
• What procedures place workers at risk of illness or injury?
• What changes can be made to correct existing problems?

Post-change assessment

• Is the change effective?
• How has the workplace been changed?
• Are things better or worse?
• How could the change be improved?

You can also use surveys to measure knowledge, attitudes, and behaviors. Write the survey in such a way that all those who read or hear it will understand the questions. Test the survey with a sample of workers before using it to find out whether the questions are understood as you intend. Surveys can be distributed in a number of ways: in person, with paychecks, by mail, e-mail, Internet, or a combination of methods. Follow-ups are usually necessary to increase participation and get the completed forms back.
It is always best to encourage the participation of your entire workforce in a survey. Often surveys lead to planned change and survey participants are more likely to feel a sense of ownership in the change. However, if you cannot afford to survey everyone in a very large workplace, select a sample that represents all important groups such as departments within a hospital or plant, and be sure to include all the groups that are anticipated to be included in the workplace change.
It is very important to establish a system that assures the confidentiality of each person’s responses, including both the collection and the reporting of the survey data, i.e., anonymous surveys and results. This can go a long way toward encouraging employees to provide honest feedback on the survey.

Interviews

◦ Interviews are one-on-one, face-to-face conversations. In these conversations, the interviewer(s) asks the same set of questions to a number of people but talking to only one person at a time. Interviews require more time and resources than surveys but provide more detailed information. Record interviews so that statements can be accurately reviewed and analyzed. Since interviews usually involve fewer people than surveys, you should interview a range of people who represent all the important groups associated with the change. One drawback to interviews is that the data can be challenging to analyze because it may be quite detailed or because there may be extra material that is not important to the evaluation.

Focus Groups

Focus groups involve gathering information and opinions that are “focused” on one subject from a small group of people (about 8 to 10 per group). These group discussions often provide insights that might not emerge in interviews. Focus groups can be used in all stages of making a safety and health change — from planning to determining effectiveness. You may want to recruit participants with similar characteristics (such as job classification) since group discussions often thrive on common experiences. Hold separate group discussions when you want to solicit opinions from supervisors and the employees they supervise. Assuring the confidentiality of such discussions is essential.

Below are tips for planning and conducting a focus group:

• Develop a list of discussion topics ahead of time.
• Determine the amount of time to be spent on each topic. (Good discussions usually require about 1 ½ – 2 hours. )
• Design questions in such a way that they encourage discussion. (Don’t ask questions that get short answers like “yes” or “true.”)
• Start the session with an “ice breaker” that gets everyone to talk. Make sure that everyone knows that they are expected to contribute.
• Have an experienced note taker attend. If you can get all participants’ permission, record the session on audio or videotape.
• Afterward, review the tape or transcript and summarize major points. If a transcript is prepared, be sure to substitute fictional names for the names of actual participants.

Observation

• Sample of people and time periods.
• Record your observations. This may involve watching people in person and recording their actions on a checklist. It could also involve recording people on videotape and then categorizing their actions later with the checklist.
• Whether you record people on tape or not, explain what you’re doing and why, and get their permission before you observe. Even though they know you’re watching, most people will quickly forget about it. Remember that the presence of an observer may affect what people do.

Environmental measures

Some safety and health changes are designed to improve the physical work environment. Two examples are noise baffles around loud equipment and extra ventilation to remove contaminants. Environmental measures can help determine whether these changes are effective. Environmental measures include air sampling and noise monitoring. This type of data gathering may require people with special equipment and training, but the data they can collect may help pinpoint the value of the change.

( learn more: photo-of-the-day-indoor-air-quality/)

Step 3: Analyze Data

• Allow team members to interpret findings independently.
• Compare members’ findings with the goals set by the team.
• Arrive at conclusions about the change on the basis of the findings.
• Summarize the results in such a way that everyone involved understands them.

After the initial analysis is complete, you may want to continue collecting data about the change. These data can serve as baseline measures for future interventions. They are also useful for determining the long-term impact of the change.

Step 4: Share Your Results

First, share your results with those affected by the change. The more you tell them about what you did and what you found, the more they will support your conclusions and your future efforts to evaluate the safety and health changes in the workplace. A good way to start the feedback process is to hold work-group meetings to present the results. Don’t worry about drawing conclusions from the results, just start with the basic findings. This approach will permit everyone to begin thinking about what the results suggest. You could also post the results in worker areas like break rooms, locker rooms, and cafeterias.
( leran more: key-risk-indicators-kris-and-its-the-relationship-to-key-performance-indicators-kpis/)

During the data analysis and results steps, be careful to maintain confidentiality. Breaches in confidentiality can affect your credibility. Do not report results in such a way that individual responses can be identified. This is especially important where there are workgroups of 3-6 people. In such circumstances, it may be necessary to report results for several workgroups, combined.

What Does It All Mean?

Making changes in the workplace is not easy. Take time to think about how you are going to evaluate your changes. Thinking through your options will provide you with the information necessary for making better decisions in the long run.

Evaluation can be very complicated or it can be relatively simple. Although the simplest methods maybe seem less “scientific,” they can still give you good information for making some important decisions. After a simple evaluation, you can decide to expand the intervention to other workgroups in your company, or consider making additional changes.

Improving worker safety and health, as well as increasing productivity, is a continual process of:

• problem identification
• determination of a solution
• solution implementation
• evaluation ->
• analysis and discussion of results
• judgments and conclusions
• new problem identification.

Your organization may benefit from evaluations done by others and vice versa. Share your evaluation results with local and national trade associations and labor unions. Some international organizations are developing solutions databases to make such information available worldwide.

( Learn more:evaluating-the-effectiveness-of-leading-indicators-and-developing-high-impact-for-safety/)

Below you can found more Forms

• Downloadable Kitchen Safety Inspection Checklist for Restaurants
• Mastering LOTO: Protecting Workers with Energy Isolation and Isolation Confirmation Certificates
• Flammable and Combustible Storage Checklist Free Download
• Secure Your Lifts:Guidelines for Safe Lifting Operations Free Planning Tool
• Sample of Accident Prevention Program ( APP) Template for General Industry Free Download
• Free ISO 14001:2015 Environmental Management System Audit Checklist Download
• Guides for Walking and Working Surfaces Safety Program
• Workshop Safety Guideline and free Posters
• Free Ergonomics Checklist for General Industry
• Work Area Safety Checklist
• Machine Safety and 43-Equipment Inspection Checklists
• Scaffold Safety self Audit and checklist
• Hot Work Controls and its Permit to work Form
• Safety Observation Report Template
• Forklift Operator’s Daily Checklist and safety Tips
• Inspecting Fall Protection Equipment Forms
• Templates: HSE Incentives and rewards
• 35 Inspection forms for Rig Check
• Chemical Risk Assessment form
• 22-Safety Inspection Checklists
• Safety Task Assessment Form
• Suspended Scaffold Pre-Operation Inspection Checklist
• Photo of the day: New worker Orientation & Safety Orientation checklist
• Grating-Decking-Floor- handrail-Removal Form
• Electrical Inspection Checklists
• E-Books: Fire Safety Logbook templates
• General Safety Guidelines and Employee Acknowledgment form
• Annual Internal Audit Form
• Mobile Scaffold Inspection checklist
• Simultaneous Operation (SIMOPS) checklist
• Temporary Construction Facilities (TCF) Inspection checklist
• HIRA, HSE Hazards & Effects Management Process (HEMP) & Risk Register Template
• Hazard Identification Plan (HIP) Template
• Ladder Inspection Form
• Free Pre-Startup Safety Review Checklist (PSSR)
• Hazard Identification Checklist
• Workplace Housekeeping Checklist
• ISO 45001:2018 READINESS CHECKLIST
• Lifting Plan Audit Checklist
• Job Safety Analysis (JSA) Forms What’s Right and Wrong?
• Electrical Isolation Permit to Work forms and checklist
• Canteen Inspection Checklist
• Work at Height Checklist
• Health Safety at Work Improvement Action Plan
• Fire Pump Daily Inspection Checklist
• Construction Site Traffic Management Plan (CSTMP) Guidance
• Safety Templates: COVID-19 Safety Plan
• Workplace Safety Inspections Forms
• Lock Removal Form
• Templates: Management of Change NEW Modified Equipment Safety Checklist
• Lifeline & Harness Inspection Guide checklist
• Contractor Pre-qualification Questionnaire Checklist
• Fall safety at construction checklist
• Construction safety Inspection checklist
• Equipment Safe Operating Procedures- SOP 61 checklist
• Permit to Work (PTW ) AUDIT CHECKLIST
• Hygiene and Sanitation Inspection Checklist
• Pressure Testing Checklist
• Crane Suspended Personnel Platform (MANBASKET) Permit
• Electric Arc Welding and Cutting Checklist
• Laboratory Inspection Checklist Form
• CRANE INSPECTION REPORT
• Scaffold Register and Inspection Checklist
• Portable Ladder Self Inspection checklist
• Process Safety Management (PSM) Compliance checklist
• OSHA Inspection Checklist 8-Pages
• Job Hazard Analysis form
• Incident Report Form
• Safety Inspection Form
• Contractor Weekly HSE Report Form
• Competent Person Designation form
• Compressed Gas Cylinders Access Control Inspection Checklist
• Emergency Drill After Action Review form
• Emergency Drill Table Top meeting Form
• Slips,Trips and Falls checklist
• Lift Plan Form
• Machines Access Control Inspection Checklists
• Camp Inspection form